INSTALLATION OF DRYWALL ANCHORS (SCREW ANCHORS)

Drywall is called different things in different places around the country.  Gyp board, gypsum wall board, drywall or sheetrock are all pretty much synonymous.  The term ‘drywall’ was originally a distinction made between it and plaster -which is applied wet.

 PLASTER WALLS

Plaster is found in older homes -roughly pre-1950s and some more expensive homes after that.  Plaster is pretty much phased out as being too expensive.  The high cost of plaster installation is driven almost entirely by the labor intensity of the construction/application  process.  Plastering is a trowel trade and in addition, the skills of the lathers are required as part of the construction of a plaster wall.  The wire lath must be installed for the plaster to adhere to.  The first (rough) coat of plaster is then applied, followed by the finish coat.

The plaster is mixed in a mixing machine, not unlike the cement mixers used to mix mortar (for brick and CMU*), and needs to be transported by wheelbarrow to the location.  As you can see, a whole gang of people are required to effect the construction of plaster walls.  *What we once called ‘cement blocks’ are termed CMU by architects, meaning ‘concrete masonry unit.’


Sponsored Ads

I worked on a new wing of a nursing home in 1967 that was designed with plaster walls.  That’s the last plaster job I saw.  One of our own homes, a brick ranch-style house, built around 1954 had plaster walls.  Someone had some money to spend there, apparently, and opted for plaster.  Prior to that we had a home built in 1898 and one built in 1902, which had plaster walls.  There was no drywall back then.  Most houses built in the 1950s, and since then, are built using drywall because it is cheaper/quicker and seems to be the defacto standard.

ANCHORING SCREWS IN PLASTER OR DRYWALL (SHEETROCK) WALLS

These anchors provide a strong point to hang something from.  Please note that as the name would imply, these drywall anchors are made for walls -generally 3/8″, 1/2″ or 5/8″  sheetrock thickness.

Self Drilling+Drywall+Anchors Installation of Drywall Wall Anchors

Self-drilling Drywall Anchors

 The ‘self-drilling’ type are the most convenient, in my estimation.  Other types are the ‘molly’ (expanding or, mushrooming type) and the toggle bolt.  All accomplish the same task -to attach something to a hollow sheet rock wall where no stud is available.  These sheetrock wall anchors (depending, of course, on the load) are not considered safe for use in ceilings, although I have used them for attaching lightweight fluorescent lighting to ceilings.  

REMOVING DRYWALL ANCHORS

The drywall anchors described above are removed as easily as they went in.  Hollow wall anchors (Molly or Toggle bolts) are removable -but, doing so will leave the ‘back-piece’ inside the wall -which is OK but, you will not be able to re-use it.  

Molly+Drywall+Anchor Installation of Drywall Wall Anchors

Molly Drywall Anchor

All types of anchors will leave a hole that will need to be filled. Not that it’s a big deal.  A little spackle and a broadknife will fix it up in no time.  Holes or gouges in drywall or plaster are easily repaired in that manner and is one of those Home Maintenance activities that you can easily accomplish yourself, if you like to do-it-yourself.

You have any thoughts on this or experience (good, bad, or funny)?  If so, why not share your experiences by commenting below.

Do you have any thoughts or experience on this (good, bad, or funny)? If so, why not share your experiences by commenting below. 

If this post is useful and / or interesting, kindly make use of the Social Media icons (up top or at bottom of page) and share it with someone -and/or, give the ‘LIKE’ button a click.  We do appreciate you stopping by.  Thank you.

Additional Info:

Drywall Information Center

Dangers of Imported Drywall

Drywall How-To Manual

 

 

lg share en Installation of Drywall Wall Anchors

Filed under: How-to Home Repair

Like this post? Subscribe to my RSS feed and get loads more!